Pipe Bully

Pipe Bully Pipe Rotator 

The Pipe Bully offers mechanical contractors and pipe shops a low cost, high quality solution for rotating pipe, tubing and solid shafts. Used with an outboard roller support, the Pipe Bully can rotate a large diameter range of pipe smoothly and efficiently. The Pipe Bully is available in two different sizes.  

The Model PB2005: 2000 Pound Capacity with an Outboard Roller Support 

The Model PB1005: 1000 Pound Capacity with an Outboard Roller Support 

Flag of USA
The Pipe Bully is Made in the U.S.A. 
Model PB1005
Model PB2005
Model PB1005 Pipe Bully Welding Positioner with MT16 chuck and RS-15 outboard roller support.

Capacity           

*Maximum Load Capacity using outboard roller support 1000 pounds
Maximum Rotation Torque 5000 in-lb
Maximum Pipe Diameter 16 inches

*Model PB1005 must be used with an outboard roller support. Chuck is fixed at
90 degrees to floor and does not tilt.

Rotation

Motor: 1/2 HP DC Variable speed.
Speed Range – Variable from 0.08 to 1.9 RPM
Speed Accuracy – 2 % of base speed.
Rotation Drive – Fully enclosed & lubricated self-locking worm gear.

Chuck – MT16 Gator 3-jaw self-centering
Maximum Outside Diameter gripping 16 inch
Minimum Outside Diameter gripping 0.625 inch
Fixed at 90 degrees to floor
Centerline of chuck to floor 32 inches.
3-jaw self-centering hardened reversible jaws.

RS-15 outboard roller support 
Maximum Load Capacity 1500 lbs.
Maximum Pipe Diameter 20 inches
Minimum Pipe Diameter 2 inches
Vertical Height adjustment 9.0 inches
Urethane rolls with sealed ball bearings
Roll to roll adjustment settings - 3
Powder coated frame with 4 anchor bolt holes.

Welding Ground Conduction – 500 Amps thru spring loaded mechanical ground.

Primary Input power – AC 115 volts 60 Hz Single Phase 15 Amp.

Controls 

External Nema 4X Control box – With Power On, Stop and Overload indicator lights.
Speed Control – One turn potentiometer
Directional Control – Forward/Reverse switch with dynamic braking resistor.
Start Stop Switch – For safety must be used to start if power is lost.
Overload Protection – 8 Amp motor fuse.
Foot Switch – Heavy Duty Remote start/stop with 25 feet of cable.
Cables – All motor, foot control and input power cable Heavy Duty 600 volt.

Frame – Heavy tube construction powder coated, Qty. 4 anchor bolt holes.

Approximate shipping Weight – 980 pounds, crate size 54” x 44” x 54”
Model PB2005 Pipe Bully Welding Positioner with MT20 chuck and RS-15 outboard roller support.

Capacity           

*Maximum Load Capacity using outboard roller support 2000 pounds
Maximum Rotation Torque 10,000 in-lb
Maximum Pipe Diameter 20 inches

*Model PB2005 must be used with an outboard roller support. Chuck is fixed at
90 degrees to floor and does not tilt.

Rotation

Motor: 3/4 HP DC Variable speed.
Speed Range – Variable from 0.06 to 1.4 RPM
Speed Accuracy – 2 % of base speed.
Rotation Drive – Fully enclosed & lubricated self-locking worm gear.

Chuck – MT20 Gator 3-jaw self-centering
Maximum Outside Diameter gripping 20 inch
Minimum Outside Diameter gripping 0.750 inch
Fixed at 90 degrees to floor
Centerline of chuck to floor 32 inches.
3-jaw self-centering hardened reversible jaws.

RS-15 outboard roller support 
Maximum Load Capacity 1500 lbs.
Maximum Pipe Diameter 20 inches
Minimum Pipe Diameter 2 inches
Vertical Height adjustment 9.0 inches
Urethane rolls with sealed ball bearings
Roll to roll adjustment settings - 3
Powder coated frame with 4 anchor bolt holes.

Welding Ground Conduction – 500 Amps thru spring loaded mechanical ground.

Primary Input power – AC 115 volts 60 Hz Single Phase 20 Amp.

Controls 

External Nema 4X Control box – With Power On, Stop and Overload indicator lights.
Speed Control – One turn potentiometer
Directional Control – Forward/Reverse switch with dynamic braking resistor.
Start Stop Switch – For safety must be used to start if power is lost.
Overload Protection – 12 Amp motor fuse.
Foot Switch – Heavy Duty Remote start/stop with 25 feet of cable.
Cables – All motor, foot control and input power cable Heavy Duty 600 volt.

Frame – Heavy tube construction powder coated, Qty. 4 anchor bolt holes.

Approximate shipping Weight – 1380 pounds, crate size 54” x 44” x 54”

Pipe Bully Welding Positioner Rotator
Pipe Bully Welding Positioner Rotator
Pipe Bully in Production.
Share by: